| Customization: | Available |
|---|---|
| Certification: | CCC, CE |
| Product Name: | Dual Power Switch |
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
This product is PC-class automatic transfer switch/It is mainly used for AC 50/60HZ,rated voltage of 400V and below,and rated working current of 1250A in a two-neutral grounded power supply system.Switch between them to ensure the reliablity and safety of power supply.
The ATS has 'normally closed','backup closed'and 'two-way open' positions.It is widely used in automatic conversion of common power supply and backup power supply of power supply system or automatic conversion and safety isolation of two load devices.
The product is compliant with the standard of GB/T14048.11 'low voltage switchgear and control equipment-part 6-1:Multifunctional electrical transfer switch electrical appliances'.
Working conditions:
1.Ambient temperature:The ambient temperature is -5ºC-+40ºC,and the average temperature should not exceed +35ºC within 24 hours.
2.Atmospheric humidity:When the maxium temperature is +40ºC,the relative humidity should not exceed 50%,and the monthly maxium relative humidity is 90%.Higher relative humidity can be allowed at lower temperature.Spercial measures should be taken for the occasional condensation caused by temperature changes.
3.Installation height:The altitude of the installation site should not exceed 2000 meters.
4.Pollution level:The environmental pollution level of the installation site is level 3
5.Usage category:The use category is :AC-33B
6.Electromagnetic environment:Acclicable to environment A.The use of this product in environment B will cause harmful electromagnetic interference,in which cause the user needs to take appropriate protective measures.
Technical parameters:
Function paramter sheet
| Item | Type A | Type C | Type D |
| Working power | AC 230V 50/60Hz | ||
| Auxilary working voltage | AC230V | ||
| Power consumption | ≤10W | ||
| Working positions | Three working positions | ||
| Operation | Automatic,manual and manual remote control operation | ||
| Working mode | automatic switching and automatic recovery/automatic switching without automtic recovery | ||
| Display | Only the power supply and closing signal LED display integrated single-phase detection | ||
| Installation | All-in-one | ||
| Voltage monitoring | Single phase detection | Single phase detection | Three-phase phase loss detection |
| Generator control | / | √ | |
| Fire-fighting linkage control | / | √(Passive contact input) | |
Technical parameter sheet
| Frame current(A) | 100 | 160 | 250 | 400 | 630 | 1000 | 1250 |
| Rated insulation voltage | 690V | ||||||
| Rated impulse withstand voltage | 8KV | ||||||
| Rated working current(A) | 16a,20A,25A,30A,40A, 50A,60A,63A,70A, 75A,80A,100A |
125a 140A 160A | 200A 225A 250A | 315A 350A 400A | 500A 630A | 800A 1000A | 1250A |
| Rated short-circuit making capacity | 8KA | 17KA | 26KA | 50KA | |||
| Rated limited short-circuit current | 120KA | ||||||
| Control voltage | AC230V | ||||||
Product functions:
| Controller code | Feature |
| Type A | 1.Common power indication and closing status indication 2.Backup power indication and closing status indication 3.Single-phase(A-phase)phase loss detection |
| Type C | 1.Common power indication and closing status indication 2.Backup power indication and closing status indication 3.Single-phase(A-phase)phase loss detection 4.Fire-fighting linkage,power generation start and stop function |
| Type D | 1.Common power indication and closing status indication 2.Backup power indication and closing status indication 3.Fire protection linkage,power generation start and stop function,three-phase phase loss detection |
){kind=link}